Products
Showing 1–24 of 142 results
-
100A 3 PHASE METER TESTER: MODEL 689B
The Model 689B meter tester uses a Digital Signal Processor
and a display processor to measure and calculate meter
errors to 0.03% or 0.1% accuracy.The Model 689B has a 3 phase switch mode current source.
For testing direct connected meters to 100A there are 6 large
6mm sockets on the front panel. Testing C.T. meters to 10A is
done using the multi pin “CURRENT” socket on the front panel.The model 3028 clip on C.T. clamps have basic phase and
ratio accuracy of 0.2%, which allows accurate testing of direct
connected polyphase and single phase meters without the
need to disconnect the meter wiring or interrupting supply to the
customer.Up to 1000 test records can be stored for review or later
downloading to a USB flash drive.
The chassis of the 689B is fitted in a rugged transit case using rubber mounts to protect it against
rough handling in the field. There is a carry handle on top and both ends of the case. -
100VA PHANTOM LOADS:MODEL 467B-30
This 3 phase phantom load is used for energising CT or Direct
connected Energy meters during commissioning or routine testing.
The 467B-30 can deliver over 100VA per phase at 100Amps / 1V.“Variacs” are used to adjust the current injection amplitude from zero
to full scale. Shrouded safety plugs and sockets are used to connect
the cables to the front panel. The input required is 240V/415V 3 phase,
4 wire and this is protected with a 3 pole circuit breaker. -
10A 3 PHASE PHANTOM LOAD: MODEL 462F
The Model 462F is designed for use with any field test set for testing polyphase CT meters.
It can be powered from the metering test block, and will test nominal 240V, 3 phase, 4 wire star connected L.V. meters or nominal 63.5V star connected H.V. meters.
It can also test nominal 110V, 3 phase, 3 wire delta connected meters.
This phantom load can be used with the Red Phase Instruments Model 679 and 679B polyphase meter testers, or any other meter tester.The 3 current outputs are variable from 0 to 100% in 1A and 10 A ranges in coarse (10%) and fine (1%) increments. Phase angle/power factor settings are available from 60º LEAD to 90º LAG in 15º increments
-
200VA Current Injection Unit: MODEL 4061
Portable current injection system designed to simulate system fault
currents and their effects on electrical and utility infrastructure
such as:
– small to medium substations
– telecom towers
– transmission pylons
– wind turbines
– rail yards and their subs
– and other disconnected earthing systems…Features:
– pure sinusoid injection current with frequency selection between
40Hz to 70Hz, in increments if 1Hz.
– on board web server including 3G/4G modem for remote status
monitoring and injection control via mobile phone.
– on board GPS for cable-less phase synchronization with Red
Phase 4031 and 4025E tuneable multimeters.
– 7 injection ranges to choose from:
160V / 1.25A on a 128 Ohm tap
120V / 1.67A on a 72 Ohm tap
80V / 2.5A on a 32 Ohm tap
60V / 3.33A on a 18 Ohm tap
40V / 5.0A on a 8 Ohm tap
30V / 6.67A on a 4.5 Ohm tap
20V / 10.0A on a 2 Ohm tap
– comes with trolley handle and wheels for ease of transport
– only 20 Kg.Please download the Preliminary data sheet for more information.
-
20A 3 PHASE PHANTOM LOAD:MODEL 473
Simple and easy to use 3 phase phantom load used in pre or post commissioning of metering and / or measurement products.
Easy way to determine correct installation and phasing of
equipment.
Supplied cable accessory is 4 metres long and is capable of providing 7.5 to 8 Amps of load current.
With shorter and thicker gauge cabling the 473 is capable of providing up to 20 Amps of load current per phase. -
2kVA Current Injection Unit: MODEL 4046
The Model 4046 is a frequency adjustable switch mode
current injection source that is used to drive the primary of
a multi tapped coupling transformer to induce variable
voltage and current magnitudes into an earth or passive
load loop at maximum power continuously if required.Typically the earth test loop / circuit consists of the earth grid
under test connected to a remote earth grid through an earth
path in the ground. To complete the loop, a return connecting
path isolated from earth, usually an ‘out of service’ feeder or
separate injection line is also used. The test current is driven
around the loop by the secondary winding of the Model 4047C
Coupling Transformer which is inserted into the loop.Frequencies from 40Hz to 70Hz can be selectively generated
by the 4046 to avoid interference with background line
frequency. Voltage drops generated by the injected current
around the earth loop are measured with a frequency
selective multimeter fixed to the current injection test
frequency.Measureable results over the test landscape can be profiled with the 4025E or 4031 frequency selective
multimeter. Both the 4025E or 4031 and the 4046 Injection system have a GPS function which is used
for position location and phase synchronization which frees up the need for phase reference cabling
during current split measurements and also provides relative positioning information so that the operator
may choose the best line of potential measurement during EPR tests to avoid mutual coupling/induction. -
3 PHASE REFERENCE STANDARD: MODEL 691
The Model 691 is a moderately priced 3 phase reference standard.
It is packaged in a 19” style bench-top case with all connections on the front panel for use in meter test benches.The software enables meter testing with all the common type of real and reactive kWh meters, both disc and electronic types.
The LCD readout shows all the parameters in the test circuit as well as meter test results.
-
8kVA Current Injection Unit: MODEL 4041
The Model 4041 is the largest of our switch mode current injection sources used for injection based testing.
This 3 phase unit works on the identical principle of operation
as our 2kVA system, however the 4041 in conjunction with
the 4042 coupling transformer have been specifically
designed to perform current injection tasks over very long
haul and demanding environments continuously at maximum
power.With our 4025E or 4031 frequency selective multimeters,
terrestrial voltage profiling is made easy with GPS positional
information available on both the 4041 and 4025E/4031 units.Another advantage of this is the ability for the two units to
synchronize phase readings, thus reducing the cabling
required when performing current split or branch
measurements and it also provides relative positioning
information so that the operator may choose the best line
of potential measurement during EPR tests to avoid
mutual coupling or induction. -
AIR COLTAN
COLORS: Navy blue-Orange, Grey-Yellow, Fluorescent yellow-Grey, Black-Red SIZE: Adjustable- micro peak, Adjustable- short peak, Adjustable- long peak Impact resistant baseball style bump cap. Highly ventilated polyester/Cotton with mesh fabric. Lined with polyethylene and comfortable EVA foam shell to absorb shocks. Adjustable size by buckle 55/62 cm. EXTERIOR : Polyester/cotton INSIDE LOOP: Polyethylene high density REINFORCEMENT OF LOOP : Foam -
AMAZONE S5 SRA
PVC SAFETY BOOT – S5 SRA
COLORS: Blue, Green
SIZES: 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47
Upper: PVC.
No Lining.
No Insole.
Outsole: Injected PVC/Nitrile. -
BRAVA 2 SMOKE
Color: SmokeSize: No SizeFrame and lens: polycarbonate
Weight: 25 gPolycarbonate single lens glasses. Soft flat spatula type arms. Integrated polycarbonate nose piece. Easy to use with safety helmet and ear defenders. Side protection. -
CA615K
HEAT-RESISTANT LEATHER HIDE WELDER’S GLOVE / KEVLAR® SEWN
COLOR: Red
SIZE: 10
High quality heat-resistant split leather (HR). Cuff with canvas lining. Kevlar® Technology sewn. American assembly. Length: 35 cm. Top quality heat-resistant leather hide, thickness: 1.2 mm to 1.4 mm.
LINED HAND : Cotton fleece.
CUFF LINED: Cotton 300 g/m².
Kevlar® sewn. -
Caderousse S3 SRC
Boots Full Grain Leather X-Large Industry Range – S3 Ci Src
-
CHEMSAFE VV835
GLOVE IN NITRILE ON POLYAMIDE LINING – FOAM NITRILE COATING PALM – 35 CM
COLOR: Green
SIZE: 08, 09, 10, 11
Double nitrile coating on polyamide lining. Third rough foam nitrile coating on palm and fingertips. Length: 35 cm. Thickness: 1.15 mm – 1.30 mm on palm. SUPPORT: 100% polyamide
COATING: Nitrile -
CONIC 200
DISTRIBUTOR OF 200 PAIRS OF EARPLUGS
COLOR: Red
SIZE: No size
Dispenser box of 200 pairs disposable polyurethane earplugs. Ø 12 mm. Individual plastic bag of 2 earplugs. Polyurethane foam. -
CONICFIR050
BAG OF 50 PAIRS OF REUSABLE THERMOPLASTIC EARPLUGS WITH CORD + STORAGE BOX
COLOR: Yellow
SIZE: No size
Box of 50 pairs of reusable TPR earplugs with fabric cord
Thermoplastic (TPR)
CORD : Textile -
Continuity Tester: MODEL ECT-4
The ECT-4 is a 4 wire Kelvin micro-ohm meter used to check the
electrical quality of metallic structures and their connection integrity
to other bonded structures in grids and electrical systems such as a
sub-station or transmission station.A custom back pack carry case houses a power source which injects
discrete levels of current at 1, 2 or 3 Amps directly between two points
in the grid connected network.The ECT-4 and it’s extension reel accessories allow this test to be
performed over small or large distances using a single Earth reference.The ECT-4 has filtering for excellent 50Hz and 60Hz rejection and also
features 5 current direction modes to further mitigate DC offset and
interference:The 5 current direction modes are:
– Forward
– Reverse
– Pulsed Forward – pulse duration can be changed in 1 second increments
– Pulsed Reverse – pulse duration can be changed in 1 second increments
– Pulsed Bipolar with or without dead time – dead time duration can be changed in 1 second incrementsMeasurements are taken with a moulded hand probe which includes twisting retractable stainless steel
pins used to make the surface connection with a bonded metallic object.The hand probe has a 5cm backlit LCD which displays the results of the bond down to a 10uΩ resolution.
The injection mode described above and current range can also be selected on the hand probe via three
tactile push buttons.The ECT-4 runs off a separate battery, also carried in the back pack, giving the operator single handed
operation and superior mobility while performing continuity tests for over 5 hours.The ECT-4 comes with all accessories necessary to begin testing straight out of the box.
Please download the data sheet for more information.
-
COUPLING TRANSFORMER: MODEL 4042/3
Model 4042 is our largest coupling transformer, with eight
secondary taps rated to 8kVA.
The 8 taps on the 4042 allows the user to adjust the injection
voltage and current to a desired value via individual tap
settings whose impedance ranges from 1 to 80 Ohms.When the correct tap is chosen and the tap menu settings
on the injection unit is set to the same value, the amplifier
will see a large reflected load and will deliver maximum
power through this tap to drive current around the earth loop.As with the lower power units, the primary of the coupling
transformer is driven by the Model 4041 injection unit up to
a nominal 320V. The various secondary taps on the 4042
translate the input from the injection unit to an output
voltage range from 90V to 800V.
Each tap on the coupling transformer is connected to a
feedback circuit which constantly senses the earth loop’s voltage and current / load.
The injection unit uses this data to maintain a constant injection current at maximum power.The 4042/3 also comes with cooling fans and a thermal cut out switch for safe operation.
-
COUPLING TRANSFORMER: MODEL 4047/C
The 4047/C is a 2kVA rated coupling transformer with eight
individual tap settings covering an impedance range from
5 to 400 Ohms.
Used in conjunction with the Model 4046 the tap selection must also be reflected in the tap menu settings of the Injection Unit which also drives the coupling transformer.When the correct tap is chosen the Amplifier will see a large reflected load and it will be able to deliver maximum power.
The unit also comes with all necessary current, voltage and
load sensing circuitry along with 2 fans and a thermal cut-out switch for safe operation over wide temperatures. -
CT & PT Tester: Model 590J-V2
Performing field test measurements of Current and Potential
Transformers has been made far simpler with the Model 590J-V2.This full featured product combines all of the metering CT test
abilities of the popular 590G-V2 model with the additional advantage of also being able to perform both protection CT
excitation tests as well as burden based inductive PT tests.The 590J-V2 eliminates the need for additional bulky accessories
usually required to perform various tests on different types of
equipment, saving the operator valuable time and money.Light weight and portable, the 590J-V2 is housed in a ruggedized
plastic case and is supplied with the necessary test cables and
attachment accessories. It is further packaged in a foam lined
transit case for safe transport.It features the following offline test capabilities:
– Burden based CT and PT ratio and phase error measurements
to an accuracy of 0.02%
– Excitation measurements of Protection Class CTs
– Optional Live CT test capability with 590F accessory
– CT and PT secondary winding resistance, PT primary included
– CT 1.6 kHz Admittance test
– Simulated Full Load inductive PT testing on up to 2 windings with
or without Junction box
– CT and PT Burden test
– CT and PT polarity check
– Batch testing of metering CTs
– No name plate CT Class Estimation
– Record download to USB Flash or optionally via Bluetooth to an Android tablet or phone.
This full featured CT and PT test instrument lowers testing costs by being simple, fool-proof and fast.
It’s capabilities allow utility personnel and test technicians to pursue the very important task of testing field
based instrument transformers for measurement losses, faults or tampering. -
CT Tester: Model 590G-V2
Since 1999, Red Phase Instruments has led the way in the manufacture of portable CT error testing equipment.
Our portable analysis method has allowed utilities around the world to test their metering CTs easier and faster than using bulky traditional methods without jeopardizing accuracy.Following feedback from our users, our Model 590G-V2 is the latest version of this successful and well proven CT error tester.
The 590G-V2 has all the features and advantages of the previous models with additional testing features, better accuracy and smaller size and weight.
In a world where cost control is gaining importance, this CT tester not only lowers testing costs by being simple, fool-proof and fast. It also allows utilities to pursue the very important (yet at many times forgotten) task of testing installed CTs for detecting tampering, and minimizing losses due to faulty CTs.
Test capabilities:
Offline
CT Ratio and phase error measurements to an accuracy of 0.02%.
CT 1.6 kHz Admittance test.
Graphical display or plot of the CT’s excitation curve.
Burden test.
Measures CT winding resistance.
Performs a CT polarity check.
PT full load simulated tests (with 590D-1 accessory)
Live
Live CT testing (with 590F accessory) -
CVT Tester: Model 590K
True burden based CVT analysis done portably!!
Features include:
Ability to test for ratio errors at up to 500VA burden.
Selectable Power Factor.
Ratio error accuracy to 0.05%.
Four selectable CVT test point standards to choose from.
Tests CVT rated to 500kV with up to 3 secondary windings.
Truly portable ~ 20kg.
Please note:
This is not a simple ratio / nameplate comparison tester.The R & D that has gone into developing this instrument is second to none.
Over 60 CVT’s from over 12 manufacturers have been carefully characterized under lab and field conditions to create a complex software
model that is able to measure a known CVT down to a 0.05% or better ratio error and even an
unknown CVT to only a 0.25% error under real load conditions.Under test conditions the 590K takes a number of measurements and characterizes the CVT.
It then calculates the performance of the CVT under different loads and applied voltage conditions to suit
any of the four common test types used on a CVT.
If other test points are required, Red Phase Instruments is able to modify these points to suit any
regulation.So when compared to traditional methods the 590K stands out as the only real portable alternative for
real load ratio assessment over a wide VA range and flexible Power Factor settings.The CVT tester uses a combination of a Digital Signal Processor and a PC104 mini computer to provide
a powerful and yet easy use instrument running on a Windows XP operating system.
A large colour display on the front panel presents a large amount of easy to follow information. -
DELTA SPORT S3 SRC
MESH/POLYURETHANE SHOES – S1P HRO SRC
COLORS: Black-Red, Blue-Yellow
SIZES: 39, 40, 41, 42, 43, 44, 45, 46, 47
Upper: Injected PU on mesh. Lining: Polyester. Insole: Removable preformed – Polyester on EVA. Outsole: Cemented – Phylon. Outsole: Rubber Nitrile. Non metallic footwear.
-
DMACHPAN
D-MACH WORKING TROUSERS IN POLYESTER COTTON
COLOR: Grey-Yellow, Grey-Orange, Black-Red
SIZE: S, M, L, XL, XXL, 3XL
Trousers. Elasticated waist on both sides. 6 pockets including 1 ruler. Twill 65% polyester 35% cotton 245 g/m².